Wanted
Moderators: Cal_Gary, T. Highway, Monkey Man, robi
Forum rules
Your Location must be included in your advertisement or it may removed without notice.
Your Location must be included in your advertisement or it may removed without notice.
Re: Wanted
Kaegi,
I have one in N. Calif.
If you know anyone headed down to the MVCC meet in Camp Plymouth this weekend I could drag it up there.
Andy
I have one in N. Calif.
If you know anyone headed down to the MVCC meet in Camp Plymouth this weekend I could drag it up there.
Andy
Re: Wanted
ashyers wrote:Kaegi,
I have one in N. Calif.
If you know anyone headed down to the MVCC meet in Camp Plymouth this weekend I could drag it up there.
Andy
I will ask a couple guys. dont think they are goingg tho
Re: Wanted
I've got one you can have free in Phoenix. You could have it complete for $200. I haven't stripped it down yet. Is a good pullout from a CDN axle/powertrain swap.
"It may be ugly, but at least it is slow!"
Re: Wanted
just me wrote:I've got one you can have free in Phoenix. You could have it complete for $200. I haven't stripped it down yet. Is a good pullout from a CDN axle/powertrain swap.
great deal but cost to get to WA too high
-
- Posts: 2
- Joined: Thu Sep 26, 2019 12:32 pm
Re: Rear Axle Housing
I think I've got one in Portland. I took it off a WC12 thinking to reinstall it later, but the gears were broken. Then I noticed that the drums and hubs didn't look like those for a WC12. I googled the hub numbers and got a listing showing they were for an M37. I think they may have installed them and blew up the gears when they didn't match those on the front axle.
Here are the dimensions:
56 5/16" between brake backing plates.
44 5/8" center-to-center at the spring supports.
Differential cover is 11 1/8" diameter.
Brake backing plates are for 14" x 2" shoes.
Hubs were Budd 45406 (14" drums).
If this is what you're looking for, you're welcome to it for free.
-Don
Here are the dimensions:
56 5/16" between brake backing plates.
44 5/8" center-to-center at the spring supports.
Differential cover is 11 1/8" diameter.
Brake backing plates are for 14" x 2" shoes.
Hubs were Budd 45406 (14" drums).
If this is what you're looking for, you're welcome to it for free.
-Don
Re: Wanted
pretty sure you have a civvy PW rear housing. Does yours have the offset diff? offset is PW and M37 (m37 being narrower) and centered are WC. a friend just gave me measurement of 54" backing plate to packing plate on an M37. the WC/PW housings are wider by about 2.375"
Re: Wanted
ive got a rear axle and a forklift 40min north of the 49th
.............................. use it ...............
-
- Posts: 2
- Joined: Thu Sep 26, 2019 12:32 pm
Re: Wanted
The one I have is centered. Guess it's a later WC. Thanks for the info.
Re: Wanted
Don in Oregon wrote:The one I have is centered. Guess it's a later WC. Thanks for the info.
if it has a 9 & 5/8 dif its early 43 to 45 WC 3/4 ton. one way to tell, if you dont have the diff in it, is the stud size. the 1/2 ton WC and the early 3/4 ton used the 8.75" diff and the mounting studs are 3/8" the 9 5/8" mounting studs are 7/16"
Re: Wanted
still looking. the one in bc had been torched
Re: Wanted
R1830 wrote:I have one on Vancouver Island
sent you a PM