Hello Crew,
The cheap a** S&S replacement speedometer I put in two years ago gave it up last weekend. I started to hear a noise and the needle went nuts and stopped at 30MPH. I thought perhaps my cable or transfer case speedo drive went. Upon pulling out the import speedometer I found the back threaded flange completely pulled out of the case. It was merely held in with cheap cement. Long story short I fetched my old speedometer. However the bracket was not on it. The import speedometer case is about .250" shorter than the originals so that clamp falls short. I cannot find my old one. If any one has an old school spare speedo clamp bracket they want to part with shoot me a PM.
Thanks.
I will post a pic of the failed import speedo later.
Thanks , David
Speedometer clamp bracket needed
Moderators: Cal_Gary, T. Highway, Monkey Man, robi
Forum rules
Your Location must be included in your advertisement or it may removed without notice.
Your Location must be included in your advertisement or it may removed without notice.
- HingsingM37
- 1SG
- Posts: 1458
- Joined: Sat Oct 20, 2007 3:43 am
- Location: North Carolina
Speedometer clamp bracket needed
David
HingsingM37
1958 M37B1
1968 M101A1 Trailer
MVPA# 33078
"Do Not Take Counsel of Your Fears"
General George S. Patton Jr.
"Those who pound their guns into plows, will plow for those who do not".
HingsingM37
1958 M37B1
1968 M101A1 Trailer
MVPA# 33078
"Do Not Take Counsel of Your Fears"
General George S. Patton Jr.
"Those who pound their guns into plows, will plow for those who do not".
Re: Speedometer clamp bracket needed
I have several old speedometers and will check about a mounting bracket and have an answer tomorrow David, have to locate the box first.
Carter
Life Member:
Delta, Peach Bottom Fish & Game Assn.
Life Member:
Delta, Peach Bottom Fish & Game Assn.
Re: Speedometer clamp bracket needed
I might have an extra bracket as well, and can check next week if Carter doesn't have one.
I noticed that the ORD 9 SNL lists two different brackets, depending on which speedo head you're using: either AC Delco or Auto-Lite.
I noticed that the ORD 9 SNL lists two different brackets, depending on which speedo head you're using: either AC Delco or Auto-Lite.
“When a long train of abuses and usurpations, pursuing invariably the same Object evinces a design to reduce them under absolute Despotism, IT IS THEIR RIGHT, IT IS THEIR DUTY, TO THROW OFF SUCH GOVERNMENT...” -Declaration of Independence, 1776
- HingsingM37
- 1SG
- Posts: 1458
- Joined: Sat Oct 20, 2007 3:43 am
- Location: North Carolina
Re: Speedometer clamp bracket needed
Thanks Carter and Elwood. The bracket that came with the new speedometer that is too short is about 2.40" OAL. I need the longer one. Below is a photo of the failed import speedometer.
David
HingsingM37
1958 M37B1
1968 M101A1 Trailer
MVPA# 33078
"Do Not Take Counsel of Your Fears"
General George S. Patton Jr.
"Those who pound their guns into plows, will plow for those who do not".
HingsingM37
1958 M37B1
1968 M101A1 Trailer
MVPA# 33078
"Do Not Take Counsel of Your Fears"
General George S. Patton Jr.
"Those who pound their guns into plows, will plow for those who do not".
Re: Speedometer clamp bracket needed
Are you sure that was glued into the speedo housing? The gray looks like anti-tamper paint. The jagged edge looks more like fatigue failure (probably caused by cheap metal).
What manufacturer made the old speedo head that you're putting back in: AC or Auto-Lite?
What manufacturer made the old speedo head that you're putting back in: AC or Auto-Lite?
“When a long train of abuses and usurpations, pursuing invariably the same Object evinces a design to reduce them under absolute Despotism, IT IS THEIR RIGHT, IT IS THEIR DUTY, TO THROW OFF SUCH GOVERNMENT...” -Declaration of Independence, 1776
Re: Speedometer clamp bracket needed
I do have an extra, just pay shipping cost only, PM me with your mailing address.
Carter
Life Member:
Delta, Peach Bottom Fish & Game Assn.
Life Member:
Delta, Peach Bottom Fish & Game Assn.
- sturmtyger380
- SFC
- Posts: 574
- Joined: Sun Oct 21, 2007 5:13 pm
- Location: Up State SC
Re: Speedometer clamp bracket needed
I am voting for metal fatigue. Is your speedometer cable housing and cable at an angle when it goes into the speedometer?
47 CJ2A
53 M38A1
52 M37
51 M38
67 M416
?? M101A1
53 M38A1
52 M37
51 M38
67 M416
?? M101A1
- HingsingM37
- 1SG
- Posts: 1458
- Joined: Sat Oct 20, 2007 3:43 am
- Location: North Carolina
Re: Speedometer clamp bracket needed
Yes, Most likely cheap metal now that I look at it closer. Cable is routed well and lines up pretty good. Old speedo is still good after 59 years LOL.
Not sure whose the old unit is?
Carter, I will be in touch. Thanks!
Not sure whose the old unit is?
Carter, I will be in touch. Thanks!
David
HingsingM37
1958 M37B1
1968 M101A1 Trailer
MVPA# 33078
"Do Not Take Counsel of Your Fears"
General George S. Patton Jr.
"Those who pound their guns into plows, will plow for those who do not".
HingsingM37
1958 M37B1
1968 M101A1 Trailer
MVPA# 33078
"Do Not Take Counsel of Your Fears"
General George S. Patton Jr.
"Those who pound their guns into plows, will plow for those who do not".