Need Canadian trans parts

Citizensoldier · Post by **Citizensoldier** » Tue Dec 16, 2008 12:14 pm

I am trying to find a rebuild kit for my ACME transmission in my M37 Canadian truck. Or any parts, seals, info, numbers to call.. Anything?? I tried Brian Ausbury with no luck.
Charles Talbert you have anything for them?
I have been told that ACME was a division of Borg Warner and there are PTO's off of some late 40's Ford trucks that will work.. Can anybody confirm this? Any info on these trans would help..

MSeriesRebuild · Post by **MSeriesRebuild** » Tue Dec 16, 2008 2:59 pm

I have 1 take-out ACME trans. Have no idea about its condition.

Citizensoldier · Post by **Citizensoldier** » Tue Dec 16, 2008 3:20 pm

How much would you want for it? Maybe pop the top and take a look? Is there a PTO on it by some lucky hand of God? I need to travel to the Cherry Point NC in the near future.. Your on the way arent you? .

MSeriesRebuild · Post by **MSeriesRebuild** » Tue Dec 16, 2008 3:34 pm

No PTO, we are about 4 hours northwest of Cherry Point. We could certainly be on your way, depending on the route you take. We are 3 miles to the east side of US highway 52 south on the Stanly County - Anson County line. Near the Fork Community below Norwood where the Pee Dee & Rocky Rivers meet. We see the mail lady, school bus, & a few tractors pass each day, that's about it for traffic.

Citizensoldier · Post by **Citizensoldier** » Fri Dec 19, 2008 9:31 am

Charles do you have the parts to rebuild the trans you have? Maybe a price on that one completely rebuilt ready to go. I noticed mine has a bigger input shaft than the US trans? I have not pulled the bell housing off yet but do Canadian trucks have a 11 inch clutch like some civi flatfenders? Do you have a rebuilt NP420 ready to go? What size input shaft do they have? I must have a winch on this truck! ..
I have only heard rumors of a PTO that will work on the ACME but I have not broken the ACME open yet. Any chance of matching a PTO gear set to it and installing that in a US PTO housing? I know, I know lots of questions...

MSeriesRebuild · Post by **MSeriesRebuild** » Fri Dec 19, 2008 3:33 pm

Citizensoldier wrote:Charles do you have the parts to rebuild the trans you have? Maybe a price on that one completely rebuilt ready to go. I noticed mine has a bigger input shaft than the US trans? I have not pulled the bell housing off yet but do Canadian trucks have a 11 inch clutch like some civi flatfenders? Do you have a rebuilt NP420 ready to go? What size input shaft do they have? I must have a winch on this truck! ..
I have only heard rumors of a PTO that will work on the ACME but I have not broken the ACME open yet. Any chance of matching a PTO gear set to it and installing that in a US PTO housing? I know, I know lots of questions...

We could build it if it only needed bearings & seal. Not sure of parts availability if it needed more than that.

Citizensoldier · Post by **Citizensoldier** » Fri Dec 19, 2008 4:59 pm

Ok.. Well.. Hmmm... Any rebuilt NP420's? Send me some price to 1cu812@charter.net.. I hope to travel your way sometime this winter.

MSeriesRebuild · Post by **MSeriesRebuild** » Fri Dec 19, 2008 5:16 pm

Citizensoldier wrote:Ok.. Well.. Hmmm... Any rebuilt NP420's? Send me some price to 1cu812@charter.net.. I hope to travel your way sometime this winter.

I don't have a single 420 at this time.

g741 · Post by **g741** » Sun Dec 21, 2008 6:22 am

Hello guys: I have two M37 Canadian transmissions, rebuilt in Canada. They are both clean and in good condition. I also have one only NOS, still in the crate 420 M37 B1 transmission. Let me know if interested. Sid

Citizensoldier · Post by **Citizensoldier** » Sun Dec 21, 2008 9:04 am

HOLY COW! Sid you have been holding back on me..

I am very interested in them.. Shoot me some prices at my regular email.. How should we ship them? Got pictures? Hope to hear from you soon.

Need Canadian trans parts

Need Canadian trans parts

Hello

Re: Hello