Where at in BC ? ? I have a buddy that does trucks in Pemberton.
Tom
Search found 312 matches
- Thu Apr 26, 2012 7:18 pm
- Forum: General M37
- Topic: Found new treasurres
- Replies: 6
- Views: 1007
- Tue Apr 24, 2012 8:07 pm
- Forum: Technical group
- Topic: LU4 winch ?
- Replies: 4
- Views: 980
Re: LU4 winch ?
I went out in the shop and pulled a top plate and came up with 14.5" center to center on the top holes where the plate bolts down.
- Mon Apr 23, 2012 7:44 pm
- Forum: Technical group
- Topic: LU4 winch ?
- Replies: 4
- Views: 980
Re: LU4 winch ?
I have new reproduction plates at Snake River 4x4.com
- Thu Apr 19, 2012 7:54 pm
- Forum: Technical group
- Topic: Military Lock Washers
- Replies: 5
- Views: 873
Re: Military Lock Washers
I have all sizes in stock.
www.snakeriver4x4.com
www.snakeriver4x4.com
- Mon Apr 16, 2012 6:06 pm
- Forum: Technical group
- Topic: Cheap Repaint.....And I Mean CHEAP!!
- Replies: 11
- Views: 2301
Re: Cheap Repaint.....And I Mean CHEAP!!
I went to a big car show recently, and there was a Corvette with a rattle can paint job. You could not tell the difference.
- Wed Apr 11, 2012 6:03 pm
- Forum: Soap box
- Topic: M37/ Powerwagon
- Replies: 11
- Views: 2074
Re: M37/ Powerwagon
It is technically not a Power Wagon, but I have restored a WC 3/4 ton and an M37 and a 46 Power Wagon. And you can almost do all three blindfolded. I guess you could say that the M37 is the brother to the Power Wagon, same genes, just a little differant look.
- Tue Apr 10, 2012 4:25 pm
- Forum: General M37
- Topic: Strange Spare Tire Mount
- Replies: 7
- Views: 1328
Re: Strange Spare Tire Mount
Okay, it looks like they took the door spare tire carrier off of a B1 and bolted it to the end of the bed. I would say that it would still be very stressful on the back of the bed side.
- Mon Apr 09, 2012 5:32 am
- Forum: Technical group
- Topic: 4 Door Concept
- Replies: 54
- Views: 11385
Re: 4 Door Concept
Friends not let friends use Handy-man jacks.
How about a suicide door.
How about a suicide door.
- Wed Apr 04, 2012 8:08 pm
- Forum: General M37
- Topic: Is There a Vendor List Somewhere?
- Replies: 4
- Views: 837
Re: Is There a Vendor List Somewhere?
Stick my site on there while you are at it.
www.snakeriver4x4.com
www.snakeriver4x4.com
- Sat Mar 24, 2012 5:58 pm
- Forum: General M37
- Topic: M151 heater install
- Replies: 2
- Views: 652
Re: M151 heater install
Depending on where you put the heater, I have had to unscrew and rotate the output duct. It puts out so much heat, I have never bothered with a defrost system.
Re: Shop Vise
The best thing I did was mount the vise to a free standing petestal - a 5" pipe welded onto a 20" truck rim. Most times a good big vise mounted on the edge of a bench is no stronger than the bench.
- Tue Jan 24, 2012 5:20 pm
- Forum: Technical group
- Topic: 24 Volts to 12 Volts How is this done ??
- Replies: 15
- Views: 3686
Re: 24 Volts to 12 Volts How is this done ??
If you have a fairly stock M37 DON'T DO IT, your much better off as far as value, ect to leave it origional.
However on the otherhand, when you swap in a modern engine and want updates, then switch to 12v.
However on the otherhand, when you swap in a modern engine and want updates, then switch to 12v.
- Wed Jan 04, 2012 6:30 pm
- Forum: Technical group
- Topic: Getting the run-flats out of a Michelin ?
- Replies: 8
- Views: 1135
Re: Getting the run-flats out of a Michelin ?
I tried today useing the motor picker, and it worked fine. Just had to coax it with a crow bar. I hate the run flat lubricant.
- Sat Dec 31, 2011 7:02 am
- Forum: Technical group
- Topic: Getting the run-flats out of a Michelin ?
- Replies: 8
- Views: 1135
Re: Getting the run-flats out of a Michelin ?
Chris, your right, never thought about the inner tube being needed on the original split ring wheel.
There should be more available from BOYCE equipment at 800-748-4269, they were asking $300.00 each.
I would call quick as the supply was limited.
There should be more available from BOYCE equipment at 800-748-4269, they were asking $300.00 each.
I would call quick as the supply was limited.
- Fri Dec 30, 2011 12:41 pm
- Forum: Technical group
- Topic: Getting the run-flats out of a Michelin ?
- Replies: 8
- Views: 1135
Re: Getting the run-flats out of a Michelin ?
Wondering if the rims on a WDX or M37 will fit these tires WITH the run-flats in them ? ?
What would be so bad about running the run-flats IF the rims fit ? ? ?
What would be so bad about running the run-flats IF the rims fit ? ? ?