Search found 113 matches
- Fri May 17, 2024 12:04 pm
- Forum: Technical group
- Topic: Turn Signals not working
- Replies: 3
- Views: 27
Re: Turn Signals not working
I have redone all the grounds and replaced bulbs. I checked all connections and cleaned and reconnected. I have lights in all the right places but no flashing. Still have the .mil flasher unit? Swap it for a 24v civilian flasher. A two pole will work. There are 3 wires going to the.mil flasher, one...
- Fri May 17, 2024 9:26 am
- Forum: General M37
- Topic: body mount questions
- Replies: 6
- Views: 45
- Fri May 17, 2024 6:43 am
- Forum: General M37
- Topic: body mount questions
- Replies: 6
- Views: 45
Re: body mount questions
Hope this helps?
I will look later today.
I will look later today.
- Wed May 15, 2024 6:10 pm
- Forum: General M37
- Topic: Winch Hole Plug
- Replies: 3
- Views: 26
Winch Hole Plug
Has anyone successfully found a plug for the winch lever hole in the drivers floor? Just doesn't seem right to tack weld a cover..
What have you used, if anything?
What have you used, if anything?
- Thu May 09, 2024 8:59 am
- Forum: Builders Blog
- Topic: New to me '52 M37
- Replies: 42
- Views: 22106
Re: New to me '52 M37
Pertronix units don't like copper plug wires Confused... This is a MIL distributor. I was told if you have the military waterproof distributor, metallic core (copper) cables are preferred. If your distributor has been replaced with a civilian type distributor, a non metallic core cable must be used...
- Mon May 06, 2024 11:30 am
- Forum: Builders Blog
- Topic: New to me '52 M37
- Replies: 42
- Views: 22106
Re: New to me '52 M37
Next question:
There are AC Delco R45 plugs in it now. The previous owner used regular wires from the .mil distributor.
The points have been changed to the Pertronix module. Any suggested change in plugs or gap?
There are AC Delco R45 plugs in it now. The previous owner used regular wires from the .mil distributor.
The points have been changed to the Pertronix module. Any suggested change in plugs or gap?
- Thu May 02, 2024 4:32 pm
- Forum: General M37
- Topic: Denton NC 2024 Rally
- Replies: 6
- Views: 138
Re: Denton NC 2024 Rally
Wanted to get there but the grandkid had a game. Priorities and such...
Maybe next year I'll get the beast started and get there. It's only 1.5hrs by car, 3hrs by M37.
Maybe next year I'll get the beast started and get there. It's only 1.5hrs by car, 3hrs by M37.
- Wed Apr 17, 2024 5:45 pm
- Forum: Builders Blog
- Topic: New to me '52 M37
- Replies: 42
- Views: 22106
Re: New to me '52 M37
Raining here but the want to drive around the lake is tempting. A 1.5hr drive would be great at 80deg.
- Mon Apr 15, 2024 2:03 pm
- Forum: Builders Blog
- Topic: New to me '52 M37
- Replies: 42
- Views: 22106
Re: New to me '52 M37
Got the signals figured out. The mil flasher and controller were toast.. swapped them out for a Signal Stat 900 and a 3 pin LED compatible flasher. Previous owner had two wires active when the brake switch is closed which screwed up the stop lamps. Wired and labled! Took off the old mechanical fuel ...
- Thu Apr 11, 2024 5:59 pm
- Forum: Technical group
- Topic: New Noise
- Replies: 9
- Views: 1084
- Wed Apr 10, 2024 3:52 am
- Forum: General M37
- Topic: Filament to LED Light Bulbs??
- Replies: 3
- Views: 1355
Re: Filament to LED Light Bulbs??
The Stop/Turn bulbs can be changed with a LED 1156 rated at 12-24v. Since the Mil housings don't have reflected interiors be sure to get the ones with LEDs on the end. 20240410_075521.jpg Output is a little brighter than the dual filament bulb. At least there's some draw reduced on the minimal 25a g...
- Thu Apr 04, 2024 1:27 pm
- Forum: General M37
- Topic: Filament to LED Light Bulbs??
- Replies: 3
- Views: 1355
- Thu Apr 04, 2024 12:27 pm
- Forum: General M37
- Topic: Filament to LED Light Bulbs??
- Replies: 3
- Views: 1355
Filament to LED Light Bulbs??
Anyone change out the filament bulbs to 24v LEDs? I'm looking for the Stop/Turn and Marker (tail) lights.
From what I can research the Stop/Turn are #1156 and are commonly replaceable with equivalent LEDs.
The markers, #1251, not so easy...
From what I can research the Stop/Turn are #1156 and are commonly replaceable with equivalent LEDs.
The markers, #1251, not so easy...
- Thu Apr 04, 2024 4:05 am
- Forum: General M37
- Topic: Oil Bath Air Cleaner Gasket
- Replies: 9
- Views: 1021
Re: Oil Bath Air Cleaner Gasket
Next is to figure out something for under the wing nut. For the metal to metal wing nut contact area I was able to reduce the internal flare with pliers. That flare prevented the removal of the wing nut. A large rubber washer covered by a metal washer now sits between the wing nut and the cleaner, ...
- Mon Apr 01, 2024 3:05 pm
- Forum: Swap Meet
- Topic: FS: M101A1 Trailer - SOLD
- Replies: 4
- Views: 1546
Re: FS: M101A1 Trailer
Dropped to $1250 for a quick sale.