Search found 29 matches
- Tue May 14, 2024 5:29 pm
- Forum: Technical group
- Topic: Winch question
- Replies: 5
- Views: 102
Re: Winch question
Thank you Gary!
- Mon May 13, 2024 6:46 pm
- Forum: Technical group
- Topic: Winch question
- Replies: 5
- Views: 102
Re: Winch question
Thank you!
- Mon May 13, 2024 5:56 am
- Forum: Technical group
- Topic: Winch question
- Replies: 5
- Views: 102
Winch question
Is the winch on an M715 the same as the one for the M37? I have one and I am trying to find out if I can use it on my M37.
Thank you!
Thank you!
- Tue Apr 02, 2024 5:09 pm
- Forum: Technical group
- Topic: Intermediate Shaft U Joints
- Replies: 2
- Views: 999
Re: Intermediate Shaft U Joints
Thank you!
- Thu Mar 28, 2024 7:39 pm
- Forum: Technical group
- Topic: Intermediate Shaft U Joints
- Replies: 2
- Views: 999
Intermediate Shaft U Joints
Anyone knows if the SKF UJ304 u joints will fit on the intermediate shaft? I read on a different thread that Napa #304 will fit so I just want to make sure the SKF UJ304 is a replacement number and fits.
Thank you in advance!
Thank you in advance!
- Tue Feb 13, 2024 6:20 pm
- Forum: Technical group
- Topic: Steering Knuckle Bearings
- Replies: 6
- Views: 1254
Re: Steering Knuckle Bearings
Thank You m-11!
- Sat Feb 03, 2024 8:09 pm
- Forum: Technical group
- Topic: Steering Knuckle Bearings
- Replies: 6
- Views: 1254
Re: Steering Knuckle Bearings
Thank you both! anyone knows the timken numbers for the bearings and cups? Maybe I can find them locally.
- Fri Feb 02, 2024 7:35 pm
- Forum: Technical group
- Topic: Steering Knuckle Bearings
- Replies: 6
- Views: 1254
Steering Knuckle Bearings
Hello, Looking for wisdom/guidence. Looking for opinions in preference between using the roller bearings on the upper side of the steering knuckle as opposed to the bronze cone. And also, Are they the same size? top and bottom I have movement, in/out, on the steering knuckles. I tried adjusting it w...
- Mon Jan 22, 2024 7:29 pm
- Forum: Technical group
- Topic: ETW1 carburetor
- Replies: 6
- Views: 1389
Re: ETW1 carburetor
Thank you!
- Sat Jan 20, 2024 7:56 pm
- Forum: Technical group
- Topic: ETW1 carburetor
- Replies: 6
- Views: 1389
Re: ETW1 carburetor
Thank you, Andy. Everything I read says it is adjusted at 3200 RPM's. Is it that it needs to be acelarated at that rate while adjusting? or that it should not be adjusted to acelerated more than that? I am not understanding the procedure on the TM well.
Have you done it?
Rafael
Have you done it?
Rafael
- Fri Jan 19, 2024 7:14 pm
- Forum: Technical group
- Topic: ETW1 carburetor
- Replies: 6
- Views: 1389
ETW1 carburetor
Hello,
Is it possible to eliminate the governor on a ETW1 carburetor? My M37 runs very slow and it does not accelerate smoothly. It is hard to rev up and dies down when going up-hill.
Rafael
Is it possible to eliminate the governor on a ETW1 carburetor? My M37 runs very slow and it does not accelerate smoothly. It is hard to rev up and dies down when going up-hill.
Rafael
- Tue Jan 09, 2024 7:36 am
- Forum: Technical group
- Topic: Front Axle Pinion Bearing
- Replies: 14
- Views: 5838
Re: Front Axle Pinion Bearing
Thank you!
- Mon Jan 08, 2024 12:04 pm
- Forum: Technical group
- Topic: Front Axle Pinion Bearing
- Replies: 14
- Views: 5838
Re: Front Axle Pinion Bearing
Hello. Thank you for the tip. I am back working on the truck. I have a local Timken dealer near my house so I am going to check there. One more question. What kind of differential is on the M37? Dana?
- Thu Dec 07, 2023 12:41 pm
- Forum: Technical group
- Topic: Front Axle Pinion Bearing
- Replies: 14
- Views: 5838
Re: Front Axle Pinion Bearing
Thank you! I'll keep posting on the progress.
- Mon Dec 04, 2023 6:21 am
- Forum: Technical group
- Topic: Front Axle Pinion Bearing
- Replies: 14
- Views: 5838
Re: Front Axle Pinion Bearing
Thank you! I will work on that soon. I am trying to get the vehicle driving in good condition before I start doing body work. Anyone knows the code for the NAVY gray paint?