I’ve done that! My Pertronix was fine, coil was bad.
I moved my M37 key to my daily driver keychain and that helps me remember to take the key.
Search found 236 matches
- Wed May 08, 2024 9:50 am
- Forum: Technical group
- Topic: Electronic Ignition problem
- Replies: 4
- Views: 91
- Mon Apr 15, 2024 6:10 am
- Forum: Technical group
- Topic: New Noise
- Replies: 9
- Views: 1055
Re: New Noise
Same noise with the belt off, and after torquing the manifold (several nuts were loose).
- Thu Apr 11, 2024 9:51 am
- Forum: Technical group
- Topic: New Noise
- Replies: 9
- Views: 1055
Re: New Noise
Same noise with the clutch in or out
- Thu Apr 11, 2024 6:06 am
- Forum: Technical group
- Topic: New Noise
- Replies: 9
- Views: 1055
New Noise
Sounds like it's coming from the dizzy. I don't think it's the generator or water pump. This is at idle:
https://youtube.com/shorts/xtPJqD4p7LM?feature=share
Anybody got ideas?
https://youtube.com/shorts/xtPJqD4p7LM?feature=share
Anybody got ideas?
- Tue Nov 28, 2023 6:38 am
- Forum: Builders Blog
- Topic: New to me '52 M37
- Replies: 42
- Views: 22034
Re: New to me '52 M37
Here is what I did. Need a 3-way key switch.
- Wed Nov 01, 2023 8:23 am
- Forum: Technical group
- Topic: Source for Brake Parts
- Replies: 5
- Views: 4039
Re: Source for Brake Parts
I always start with John at Midwest.
- Fri Oct 06, 2023 3:55 pm
- Forum: General M37
- Topic: Windshield Hold-down Bracket?
- Replies: 2
- Views: 1505
Re: Windshield Hold-down Bracket?
You’re missing the hold down latches. They look like the hold down latches for the hood but with a different handle. Midwest Military has them im sure.
- Sun Jul 16, 2023 10:59 am
- Forum: Builders Blog
- Topic: Grandpa’s M37
- Replies: 166
- Views: 36966
Re: Grandpa’s M37
1st Parade!
I was worried about engine temps but that was not an issue. Hardest part was finding a good gear. 1st Low was too slow, 2nd low was too fast. I needed a 1 1/2 gear!
I was worried about engine temps but that was not an issue. Hardest part was finding a good gear. 1st Low was too slow, 2nd low was too fast. I needed a 1 1/2 gear!
- Thu Jul 13, 2023 10:16 am
- Forum: General M37
- Topic: Engine paint color
- Replies: 5
- Views: 1483
Re: Engine paint color
I’ve heard from several sources the engines were Chrysler Silver when they left the factory.
- Mon Jul 10, 2023 4:26 am
- Forum: Technical group
- Topic: Transfer Case Output Seal
- Replies: 10
- Views: 3095
Re: Transfer Case Output Seal
None, it is an interference fit. Once you put one on you’ll see there is no need for sealant.
- Tue Jun 27, 2023 8:02 am
- Forum: Builders Blog
- Topic: M37B3 Project
- Replies: 83
- Views: 55702
Re: M37B3 Project
Tank Renu was worth the money in my experience so far.
- Sun Jun 18, 2023 5:01 am
- Forum: Technical group
- Topic: Transfer Case Output Seal
- Replies: 10
- Views: 3095
Re: Transfer Case Output Seal
You can repair it by removing the flange. Most likely the seal has worn some grooves into the shaft. You’ll want to redi sleeve it as well as installing a new sleeve. Not a hard job, as long as you have big cheater bars.
- Wed May 24, 2023 5:37 am
- Forum: Builders Blog
- Topic: New to me '52 M37
- Replies: 42
- Views: 22034
Re: New to me '52 M37
Before cutting up the threads with the stud remover, did you try red loctite on the outer nut?
- Tue May 09, 2023 5:17 am
- Forum: Technical group
- Topic: Drag Link Removal
- Replies: 4
- Views: 1205
Re: Drag Link Removal
Basically, except the pieces won’t fall out. Put the arms on the bench and note how the springs and plates come out the end of tubes.
- Wed Apr 05, 2023 9:30 am
- Forum: Builders Blog
- Topic: Grandpa’s M37
- Replies: 166
- Views: 36966
Re: Grandpa’s M37
Thanks, I might use copper or brass for the rivets so they don’t rust. And easy to get.