g741.org

I have parts from 2 different 52 m37's. I'm going to swap out my 230 for a v8. and I have some remnants from my parts truck that I would like to see go away. So I have for sale

original engine (was running but low compression)

intake & exhaust manifolds

Good starter

2 generators (don't know if they work but looks ok)

mechanical voltage reg.

solidstate voltage reg.

Original fuel pump (Was working, but would definitely rebuild)

Carter BBS Carb (not original but will run on 230 also should be rebuilt)

Original military Dist. with 6 original wires (was running appears good)

oil filter housing

Original early trans (I had the top cover off of this to inspect it and everthing seemed tight. Also have driven it, and it ran through the gears nicely. was rebuilt by the army in '72)

Clutch flywheel and pressure plate

original transfer case from my parts truck (seems ok)

Fairly complete chassis from parts truck. (rear diff and Axle shafts are gone, and I'm probably gonna hang on to the front axle, But everything else is fair game)

Remnants of Cab from parts truck (I have started to cut parts off of it for repair But cowl and dash areas are pretty good as well as other areas)

Misc. 24v guages of unknown conition

There's more stuff I'm sure I'm just forgetting so ask.

Make me an offer on what you want I'm very reasonable. I'm willing to ship, but no I don't know how much its gonna cost to ship it. But, if you come pick something up, you might find some other stuff I haven't listed yet because I just haven't decided if I'm gonna keep it or not.

BTW I can send you pics if wanted

thanks
Brett

Brett,
PM Sent. Can you provide pics of engine if not too much trouble?

Fuel pump spoken for

Thanks
Brett

I've added some pics to my gallery here under Brett Bunnell. Heres just a couple.




If there's something you're interested in Make me an offer!! I don't really know what this stuff is worth. BTW everything is located In Murfreesboro,TN Just outside of Nashville

Thanks
Brett

I've sold some stuff, but I still have more to sell
These are no longer available
Parts cab
Dist, plugs, wires
Fuel pump
Int& exh Manifold

I still have a lot left
Rebuildable engine
Clutch
Good trans
transfer case
Generators and regulators
Chassis and suspension parts
Alot more, just ask

Thanks
Brett

Still looking to get rid of some of this stuff. I've bought a donor vehicle for my V8 swap and I need room in the garage. I thought I'd throw some prices out and see if that helps. I'll still listen to offers as well.

Engine $100
Trans $100
2 generators 1 mech reg 1 SS reg 2 cables $40
Good starter $40

Drop me a PM if you have any questions. I'm willing to ship, but I may charge a little extra to crate up the big stuff.

Thanks
Brett

Hay Brett, Brett here. I'm looking for E-brake band and all the hardware to mount it. Do you have any of this stuff ? Thanks. Brett

Brett,
I've got an extra parking brake assembly, but it will definitely need to be relined. I'm not sure how big of a deal that is. Drop me a PM if you're interested.

thanks,
Brett

Hi,
I'm looking for a bellhousing from the 230 engine. Please let me know if you got. 347 200 3015.
Thanks
Bob

Do you have a speedometer cable?

I'm pretty sure I have a Speedometer cable, but I beleive the rubber on the out side of it is not the prettiest. I can send you a pic tomorrow if you want.

Also I didn't realize I never up dated this. But I have sold alot of parts. The eng & trans are gone, as well as the cab. I do still have a transfer case, a windshield frame that is salvageable, a couple of radiators, some front end sheetmetal, and lots of odds and ends, so just ask.

Thanks
Brett

Hi Brett,
Do you still have the electronic voltage regulator?
Thanks,
Tim

Tim,
Sorry but the regulators and generators have been sold as well.

Thanks
Brett

Do you have a good driver and passinger doors?

I have a fixable Driver's door. It looks like it made pretty good contact with the front fender. There is a pic of the bottom edge of the door in the photo gallery under Brett Bunnell. The door is pretty solid other than that. I'm planning on using the passenger door off of that truck, and it looks pretty much the same. let me know if you're interested

Thanks
Brett