Page 1 of 2

M37 v PW radiator caps

Posted: Mon Jan 11, 2016 10:22 am
by Kaegi
does anyone know it the caps between M37 and Power Wagons are the same?

Re: M37 v PW radiator caps

Posted: Mon Jan 11, 2016 6:48 pm
by just me
They do, but there are two different caps. One is for a wider notch than the other on the neck.

Re: M37 v PW radiator caps

Posted: Mon Jan 11, 2016 8:53 pm
by Kaegi
wider notch in the neck? but cap will go on either one?

Re: M37 v PW radiator caps

Posted: Wed Jan 13, 2016 4:38 am
by just me
Wide tab won't fit narrow notch neck.

Re: M37 v PW radiator caps

Posted: Wed Jan 13, 2016 9:50 am
by Kaegi
what is the pressure rating on the M37 caps?

Re: M37 v PW radiator caps

Posted: Wed Jan 13, 2016 12:09 pm
by isaac_alaska
Not much, if any, if i remember right. I don't think it's a pressurized system. so the cap basically just keeps the coolant from sloshing out, but doesn't hold back any real pressure

Re: M37 v PW radiator caps

Posted: Wed Jan 13, 2016 12:24 pm
by w30bob
M37 cap is rated for 4 psi.

bob

Re: M37 v PW radiator caps

Posted: Wed Jan 13, 2016 1:03 pm
by isaac_alaska
thanks Bob, much more accurate than my answer!

Re: M37 v PW radiator caps

Posted: Wed Jan 13, 2016 7:59 pm
by w30bob
Hi Isaac,

Don't be so hard on yourself............4 psi is basically nothing! :mrgreen:
The only reason I remember that is because there was a discussion on here and it seems the alternate vendor part numbers for the cap in some peoples lists are all 7 psi caps. Does the 3 psi difference really make a difference? Probably not, but it does raise the boiling point of water a bit. But we shouldn't be running straight water for coolant........now should we?

Now what the original cap actually looks like.......that seems to still be a bit of a mystery. If anyone has what they know to be the original radiator cap........please post a pic.

thanks,
bob

Re: M37 v PW radiator caps

Posted: Thu Jan 14, 2016 4:56 pm
by Chris P
My radiator has a metal tube built in that runs from the filler neck across the top of the radiators and then down the side. So wouldn't that mean that there is no pressure in the system no matter what cap is used? Thus you can use any cap that fits?

I assumed that this opening is why the manual says to only fill the radiator to 2.5 inches from the top of the neck, though I'm still surprised that nothing ever sloshes out of that tube. At least nothing that I've noticed.

Re: M37 v PW radiator caps

Posted: Thu Jan 14, 2016 5:33 pm
by isaac_alaska
that tube is actually above the sealing point, so as long as the cap is "sealed" nothing will ever reach the tube. if the engine heats to the point that water has to go somewhere (out the cap) that tube is there so that when the seal is breached, any water will exit through the tube rather than spraying out from under the cap in all directions

Re: M37 v PW radiator caps

Posted: Tue Jan 19, 2016 12:56 pm
by Chris P
Isaac, thanks for the clarification.

Re: M37 v PW radiator caps

Posted: Fri Feb 05, 2016 11:41 pm
by Kaegi
thanks for the answers. good thread. does anyone carry NOS M37 caps?

Re: M37 v PW radiator caps

Posted: Sat Feb 06, 2016 3:07 am
by just me
MWM has them.

Re: M37 v PW radiator caps

Posted: Sat Feb 06, 2016 10:36 am
by Kaegi
just me wrote:MWM has them.
thanks