Page 1 of 1
Front Axle Inner Seal
Posted: Wed Dec 04, 2013 3:15 pm
by bill monahan
Have my front axle shafts out to repair oil leak from diff. Is it possible to remove and replace oil seal without removing bronze bushing ? Would sure be nice if I could.
Re: Front Axle Inner Seal
Posted: Thu Dec 05, 2013 12:20 am
by Cal_Gary
Not that I'm aware of.
Gary
Re: Front Axle Inner Seal
Posted: Fri Dec 06, 2013 12:02 pm
by Kaegi
nope. they both come out together. with the right tool you wont damage the bushing.
Re: Front Axle Inner Seal
Posted: Sat Dec 07, 2013 6:31 am
by bill monahan
Thanks guys. I'm modifying my slide hammer to see if that works. I have my doubts though.
Re: Front Axle Inner Seal
Posted: Mon Dec 09, 2013 2:38 pm
by pwrwagonfire
When I replaced this seal, I was advised by members on SS to use a slide hammer. I was able to rig a flat hook to the end of my slide hammer, and slowly worked it around the seal in a circle. Worked fine for me!
Let us know how you do it.
-T
Re: Front Axle Inner Seal
Posted: Wed Dec 11, 2013 6:07 am
by bill monahan
Gonna buy a new slide hammer today that has a hook type attachment. I'll let you know how I made out.
Re: Front Axle Inner Seal
Posted: Sun Dec 15, 2013 9:09 am
by bill monahan
Anyone out there that has a front axle bushing removal tool ? I've tried everything even a homebuilt tool I made. The bushing is really really stuck. A member, M15256, posted that he has one and is willing to lend it out but he hasn't been on here for a while. Really don't want to buy one for $119 from VPW. Will gladly pay shipping both ways. I live in NJ.
Re: Front Axle Inner Seal
Posted: Sun Dec 15, 2013 9:22 am
by Kaegi
http://www.ebay.com/itm/OTC-Rear-Axle-B ... 5478wt_902
lot less money here. pretty sure it will fit. I would ask for the measurements before buying
Re: Front Axle Inner Seal
Posted: Sun Dec 15, 2013 11:07 am
by bill monahan
Thanks for the tip. It should fit my slide hammer. Placed a bid. Hey, for that price I can't go wrong !
Re: Front Axle Inner Seal
Posted: Mon Dec 16, 2013 12:04 am
by Cal_Gary
If all else fails, pull the center chunk and run a long piece of metal stock from one side to the other, aligining it on the inside of the seal/bushing then drive it out with a big hammer--that's how I did mine.
Gary
Re: Front Axle Inner Seal
Posted: Mon Dec 16, 2013 7:04 am
by bill monahan
Yeah, that is the last resort. Hope I don't have to do that. Thanks.
Re: Front Axle Inner Seal
Posted: Tue Dec 17, 2013 7:05 am
by Sal
Now would be a good time to check your steering Knuckles out while you have everything apart..
Re: Front Axle Inner Seal
Posted: Sun Dec 29, 2013 10:00 am
by bill monahan
Ok, got those suckers out. I won the bid on ebay ( had to pay $36 for a set of three). Of course it required a 5/8 thread slide hammer, mine was 1/2. Rented a 5/8 slide hammer from PepBoys, free rental. Awaiting new seals from Midwest. I suspected a bad seal on right side because of oil leak at knuckle. Sure enough, there was a small puddle of oil laying inside of knuckle. Thanks to everyone who responded, really helped a lot. Btw, should I use some type of flange sealant on those seals when I put them in ?