Page 1 of 2
Parting out M43
Posted: Thu Aug 11, 2011 7:09 am
by Jim Branson
Just brought it home yesterday, its been sitting for 25 years untouched. Not sure what is all in the inside yet as it is full of misc car/truck parts. Located in north central Florida. Can deliver up to southwest Georgia. Thanks!
jjbdodge@aol.com
Re: Parting out M43
Posted: Mon Aug 15, 2011 4:23 am
by moose3d
Is the rear step and sliding door in there? How much for them?
Re: Parting out M43
Posted: Mon Aug 15, 2011 12:57 pm
by Jim Branson
The sliding door is there and complete, it even has the roll up canvas curtain. The rear step is there also. Once I have gone through the whole truck I will post the M43 parts with pricing and take pics. Thanks!
Re: Parting out M43
Posted: Mon Aug 15, 2011 1:45 pm
by moose3d
OK, thanks.
Re: Parting out M43
Posted: Tue Oct 11, 2011 9:14 am
by Jim Branson
Should be finished with it this weekend!
Re: Parting out M43
Posted: Sat Oct 15, 2011 2:37 pm
by Jim Branson
Sliding compartment door, rollers froze up $75
Gas tank access plate $10
Gas filler trim piece $5
Compartment door lids $5 each
If there is anything else not listed that you might need just ask!
Pics are in the gallery under my name.
Prices are for pickup only. Silver Springs, Fl 34488
I can email pics.
jjbdodge@aol.com
Thanks for looking!
Jim
Re: Parting out M43
Posted: Sat Dec 24, 2011 6:51 pm
by joew
Jim -
Still have the M43 parts for sale? I saw the list you posted in October. Can you provide an updated list?
Thanks.
Joe W.
Re: Parting out M43
Posted: Mon Dec 26, 2011 6:05 am
by Jim Branson
Joe, the list is still good. Parts that have been paid for are deleted from the list. Parts that have not been paid for but I'm holding for someone are marked SALE PENDING. Thanks!
Jim
Re: Parting out M43
Posted: Mon Dec 26, 2011 10:54 am
by moose3d
I will take the rear step. Can you figure shipping to 03576? Let me know and I will send payment. If the rear step trim plates don't sell I will take them too.
Thanks
Dave
Re: Parting out M43
Posted: Mon Dec 26, 2011 11:42 am
by sturmtyger380
Have you thought about taking your parts to the Fl MVPA show in Feb down at the Belleview Flea Market?
Re: Parting out M43
Posted: Mon Dec 26, 2011 12:21 pm
by poor rich
Does it have the same doors as the M37, I still need a drivers side door and glass.
Rich
Re: Parting out M43
Posted: Mon Dec 26, 2011 3:00 pm
by Jim Branson
Dave, I can do that for you after the 1st.
I can bring parts to the show if someone let's me know what they want.
Rich, doors are the same but both were rusted out and scraped.
Thanks!
Jim
Re: Parting out M43
Posted: Mon Dec 26, 2011 3:37 pm
by poor rich
NUTS!
Rich
Re: Parting out M43
Posted: Wed Jan 04, 2012 11:05 am
by Jim Branson
Dave, can you send me your email address? I would like to send new pics of the step.
Thanks, Jim.
Re: Parting out M43
Posted: Wed Jan 04, 2012 4:34 pm
by moose3d
My email is
moose3d@gmail.com
Thanks
Dave